1 files changed, 188 insertions, 0 deletions
diff --git a/src/bin/luchie.rs b/src/bin/luchie.rs
new file mode 100755
index 0000000..7dedc8d
--- /dev/null
+++ b/src/bin/luchie.rs
@@ -0,0 +1,188 @@
+#![no_std]
+#![no_main]
+
+//extern crate panic_semihosting;
+
+use luchie::{
+    cirque::Cirque,
+    log, logger, logln,
+};
+
+use cortex_m::{
+    asm::{bkpt, wfi},
+    interrupt,
+};
+use cortex_m_rt::entry;
+use embedded_hal::spi;
+use stm32f1xx_hal::{
+    pac,
+    prelude::*,
+    serial::{Config, Serial, StopBits, WordLength},
+    spi::Spi,
+    usb::{self, UsbBus},
+};
+use usb_device::prelude::*;
+use usbd_serial::{SerialPort, USB_CLASS_CDC};
+
+#[entry]
+fn main() -> ! {
+    let dp = pac::Peripherals::take().unwrap();
+
+    let mut flash = dp.FLASH.constrain();
+    let rcc = dp.RCC.constrain();
+
+    let clocks = rcc
+        .cfgr
+        .use_hse(8.MHz())
+        .sysclk(72.MHz()) // TODO: gd32 can get up to 120MHz
+        // .pclk1(24.MHz()) // TODO: causes issues with gd32 usb (dropped packets) and garbled usart1 output
+        .freeze(&mut flash.acr);
+
+    assert!(clocks.usbclk_valid());
+
+    let mut gpiob = dp.GPIOB.split();
+    let mut led = gpiob.pb2.into_push_pull_output(&mut gpiob.crl);
+    led.set_low();
+
+    let mut afio = dp.AFIO.constrain();
+    let mut gpioa = dp.GPIOA.split();
+
+    let tx_pin = gpioa.pa9.into_alternate_push_pull(&mut gpioa.crh);
+    let rx_pin = gpioa.pa10;
+    let serial = Serial::usart1(
+        dp.USART1,
+        (tx_pin, rx_pin),
+        &mut afio.mapr,
+        Config::default()
+            .baudrate(115200.bps())
+            .wordlength(WordLength::Bits8)
+            .parity_none()
+            .stopbits(StopBits::STOP1),
+        clocks,
+    );
+    let (tx, _) = serial.split();
+
+    logger::init(tx);
+
+    logln!("🐁 luchie starting…");
+
+    // cirque spi connections to spi1:
+    //
+    // pb0 - dr
+    // pa4 - ss1
+    // pa5 - clk1
+    // pa6 - miso1
+    // pa7 - mosi1
+
+    logln!("👆 init trackpad");
+    // TODO: hook an interrupt up to the dr pin to trigger a poll.
+    //let dr_pin = gpiob.pb1.into_pull_down_input(&mut gpiob.crl);
+    let sck_pin = gpioa.pa5.into_alternate_push_pull(&mut gpioa.crl);
+    let miso_pin = gpioa.pa6;
+    let mosi_pin = gpioa.pa7.into_alternate_push_pull(&mut gpioa.crl);
+    let cs_pin = gpioa.pa4.into_push_pull_output(&mut gpioa.crl);
+    let mut spi = Spi::spi1(
+        dp.SPI1,
+        (sck_pin, miso_pin, mosi_pin),
+        &mut afio.mapr,
+        spi::MODE_1,
+        1_000_000.Hz(), // pinnacle supports up to 13mhz
+        clocks,
+    );
+    let mut cirque = match Cirque::new(cs_pin, &mut spi, clocks.sysclk().raw()) {
+        Ok(c) => c,
+        Err(e) => {
+            logln!("err: {:?}", e);
+            panic!();
+        }
+    };
+
+    logln!("🖥️ init usb");
+    // BluePill board has a pull-up resistor on the D+ line.
+    // Pull the D+ pin down to send a RESET condition to the USB bus.
+    // This forced reset is needed only for development, without it host
+    // will not reset your device when you upload new firmware.
+    let mut usb_dp = gpioa.pa12.into_push_pull_output(&mut gpioa.crh);
+    usb_dp.set_low();
+    // let mut delay = dp.TIM2.delay_us(&clocks);
+    // delay.delay_ms(10u8);
+    cortex_m::asm::delay(clocks.sysclk().raw() / 100);
+
+    let usb = usb::Peripheral {
+        usb: dp.USB,
+        pin_dm: gpioa.pa11,
+        pin_dp: usb_dp.into_floating_input(&mut gpioa.crh),
+    };
+    let usb_bus = UsbBus::new(usb);
+
+    let mut serial = SerialPort::new(&usb_bus);
+
+    let mut usb_dev = UsbDeviceBuilder::new(&usb_bus, UsbVidPid(0xdead, 0xbeef))
+        .manufacturer("Fake company")
+        .product("Serial port")
+        .serial_number("TEST")
+        .device_class(USB_CLASS_CDC)
+        .build();
+
+    logln!("🎉 luchie started!");
+    loop {
+        // logln!(".");
+        if let Ok(mut td) = cirque.poll(&mut spi) {
+            td.scale_to(1920, 1080);
+            logln!("td: {:?}", td);
+        }
+
+        if !usb_dev.poll(&mut [&mut serial]) {
+            continue;
+        }
+
+        let mut buf = [0u8; 64];
+
+        match serial.read(&mut buf) {
+            Ok(count) if count > 0 => {
+                led.set_high();
+
+                // Echo back in upper case
+                for c in buf[0..count].iter_mut() {
+                    if 0x61 <= *c && *c <= 0x7a {
+                        *c &= !0x20;
+                    }
+                }
+
+                let mut write_offset = 0;
+                while write_offset < count {
+                    match serial.write(&buf[write_offset..count]) {
+                        Ok(len) if len > 0 => {
+                            write_offset += len;
+                        }
+                        _ => {}
+                    }
+                }
+                led.set_low();
+            }
+            _ => {}
+        }
+    }
+}
+
+#[panic_handler]
+fn panic(info: &core::panic::PanicInfo) -> ! {
+    interrupt::free(|_cs| {
+        log!("!!! panic ");
+        if let Some(loc) = info.location() {
+            log!("in {}:{} ", loc.file(), loc.line());
+        }
+        if let Some(msg) = info.payload().downcast_ref::<&str>() {
+            log!("⇒ {} ", msg);
+        }
+        logln!("!!!");
+    });
+    spin();
+}
+
+fn spin() -> ! {
+    bkpt();
+    loop {
+        wfi();
+    }
+}