#![no_std]
#![no_main]

//extern crate panic_semihosting;

mod cirque;
mod led;
mod log;

use cirque::Cirque;
use led::LED;

use cortex_m::{
    asm::{bkpt, wfi},
    interrupt,
};
use cortex_m_rt::entry;
use embedded_hal::spi;
use stm32f1xx_hal::{
    pac,
    prelude::*,
    serial::{Config, Serial, StopBits, WordLength},
    spi::Spi,
    usb::{self, UsbBus},
};
use usb_device::prelude::*;
use usbd_serial::{SerialPort, USB_CLASS_CDC};

#[entry]
fn main() -> ! {
    let dp = pac::Peripherals::take().unwrap();

    let mut flash = dp.FLASH.constrain();
    let rcc = dp.RCC.constrain();

    let clocks = rcc
        .cfgr
        .use_hse(8.MHz())
        .sysclk(72.MHz()) // TODO: gd32 can get up to 120MHz
        // .pclk1(24.MHz()) // TODO: causes issues with gd32 usb (dropped packets) and garbled usart1 output
        .freeze(&mut flash.acr);

    assert!(clocks.usbclk_valid());

    let mut gpiob = dp.GPIOB.split();
    let mut led = LED::new(gpiob.pb2, &mut gpiob.crl);

    let mut afio = dp.AFIO.constrain();
    let mut gpioa = dp.GPIOA.split();

    let tx_pin = gpioa.pa9.into_alternate_push_pull(&mut gpioa.crh);
    let rx_pin = gpioa.pa10;
    let serial = Serial::usart1(
        dp.USART1,
        (tx_pin, rx_pin),
        &mut afio.mapr,
        Config::default()
            .baudrate(115200.bps())
            .wordlength(WordLength::Bits8)
            .parity_none()
            .stopbits(StopBits::STOP1),
        clocks,
    );
    let (tx, _) = serial.split();

    log::init(tx);

    logln!("luchie starting…");

    // cirque spi connections to spi1:
    //
    // pb0 - dr
    // pa4 - ss1
    // pa5 - clk1
    // pa6 - miso1
    // pa7 - mosi1

    logln!("init trackpad");
    let dr_pin = gpiob.pb0;
    let sck_pin = gpioa.pa5.into_alternate_push_pull(&mut gpioa.crl);
    let miso_pin = gpioa.pa6;
    let mosi_pin = gpioa.pa7.into_alternate_push_pull(&mut gpioa.crl);
    let cs_pin = gpioa.pa4.into_push_pull_output(&mut gpioa.crl);
    let mut spi = Spi::spi1(
        dp.SPI1,
        (sck_pin, miso_pin, mosi_pin),
        &mut afio.mapr,
        spi::MODE_1,
        1_500_000.Hz(),
        clocks,
    );
    let mut cirque = match Cirque::new(cs_pin, dr_pin, &mut spi, clocks) {
        Ok(c) => c,
        Err(e) => {
            logln!("err: {:?}", e);
            panic!();
        }
    };

    logln!("init usb");
    // BluePill board has a pull-up resistor on the D+ line.
    // Pull the D+ pin down to send a RESET condition to the USB bus.
    // This forced reset is needed only for development, without it host
    // will not reset your device when you upload new firmware.
    let mut usb_dp = gpioa.pa12.into_push_pull_output(&mut gpioa.crh);
    usb_dp.set_low();
    // let mut delay = dp.TIM2.delay_us(&clocks);
    // delay.delay_ms(10u8);
    cortex_m::asm::delay(clocks.sysclk().raw() / 100);

    let usb = usb::Peripheral {
        usb: dp.USB,
        pin_dm: gpioa.pa11,
        pin_dp: usb_dp.into_floating_input(&mut gpioa.crh),
    };
    let usb_bus = UsbBus::new(usb);

    let mut serial = SerialPort::new(&usb_bus);

    let mut usb_dev = UsbDeviceBuilder::new(&usb_bus, UsbVidPid(0xdead, 0xbeef))
        .manufacturer("Fake company")
        .product("Serial port")
        .serial_number("TEST")
        .device_class(USB_CLASS_CDC)
        .build();

    logln!("luchie started!");
    loop {
        logln!(".");

        if let Ok(mut td) = cirque.poll(&mut spi) {
            td.scale_to(1920, 1080);
            logln!("td: {:?}", td);
        }

        if !usb_dev.poll(&mut [&mut serial]) {
            continue;
        }

        let mut buf = [0u8; 64];

        match serial.read(&mut buf) {
            Ok(count) if count > 0 => {
                led.on();

                // Echo back in upper case
                for c in buf[0..count].iter_mut() {
                    if 0x61 <= *c && *c <= 0x7a {
                        *c &= !0x20;
                    }
                }

                let mut write_offset = 0;
                while write_offset < count {
                    match serial.write(&buf[write_offset..count]) {
                        Ok(len) if len > 0 => {
                            write_offset += len;
                        }
                        _ => {}
                    }
                }
            }
            _ => {}
        }

        led.off();
    }
}

#[panic_handler]
fn panic(info: &core::panic::PanicInfo) -> ! {
    interrupt::free(|_cs| {
        log!("!!! panic ");
        if let Some(loc) = info.location() {
            log!("in {}:{} ", loc.file(), loc.line());
        }
        if let Some(msg) = info.payload().downcast_ref::<&str>() {
            log!("⇒ {} ", msg);
        }
        logln!("!!!");
    });
    spin();
}

fn spin() -> ! {
    bkpt();
    loop {
        wfi();
    }
}